Mack Amplifiers "HeatSeeker" HS18 All Tube Head
Product Description
Power Amp Distortion - Key To Great Tone!
The HS-18’s tone is defined by power amplifier overdrive.
Turning up the amp’s volume and letting the preamp signal overdrive the power tubes produces natural, harmonically complex - British voiced - crunch and distortion.
Addictive Chime The Heatseeker cleans up very well with changes in guitar volume. With the amp at full volume, adjusting your guitar's output produces anything from crystalline clean tones, to full on roaring distortion.
The ‘Character’ switch provides further tonal flexibility by adjusting the gain and bass output using a simple three-way switch.
Finally, the Heatseeker HS-18 thrives on overdrive and distortion pedals. Set the amp volume for a suitable clean tone and slam it into creamy, thick crunch and distortion tones with the click of a switch. Great for recording, practicing and getting a little extra slam at a gig!
Circuit Design Tubes.The Heatseeker HS-18 features a 12AX7 tube operating in a parallel triode configuration for the preamp.
Running the dual triode sections of the 12AX7 in parallel produces higher gain than a single section and lower noise than cascading one section into the other. It also produces very warm tube tone.
Another 12AX7 serves as the phase inverter and two EL84s make up the power amplifier producing about 18 watts of power.
Power Supply.The HS-18 features solid-state rectification. This means that devices called silicon diodes convert the incoming alternating current power into the direct current power the rest of the circuit needs.
Many vintage and boutique amps use tube rectifiers because they produce desirable ‘sag’. Circuitry downstream of the SS rectifiers in your Heatseeker does the same thing. You avoid the extra cost of tube rectification and the additional heat produced by the rectifier tube. You get sag that is indistinguishable from a tube rectifier set up
Controls . A volume control and single tone control reside between the preamp and phase inverter.The tone control rolls off high frequencies to voice the top end of the amp.
The lack of bass and middle tone controls restricts the amount of tone shaping, however it also reduces signal loss inherent in passive tone controls.
The fewer passive controls in the signal chain, the larger the signal getting to the phase inverter and on to the power section. This is a key factor in the Heatseeker’s ability to produce more volume than expected from an 18-watt amp and to drive the power amp into the crunch and distortion zone.
Character Switch . The Character switch does what its name implies: changes the tonal character of the amp.
There are three settings:
Hot. Ultra rich and warm tube tone. Medium gain. Burn. Aggressive high-mids, controlled bottom end, classic crunch and distortion tones. High gain. Great for dark sounding humbuckers. Melt. Big bottom, aggressive throughout the frequency spectrum. Roaring crunch and distortion. Highest gain. Great for producing ‘huge’ distorted tone from single coil guitars. There you have it: simple, effective, useful tone shaping. You’ll find that the switch positions match well with different songs and musical styles.
Heatseeker specs Handmade, hand wired using an eyelet circuit board with Teflon wire and lead-free solder Each Heatseeker undergoes a 59 point bench test prior to two playing tests 18 watts 2 X EL84 power tubes, cathode biased 2 x 12AX7 preamp tubes Solid state rectification with ‘sag’ circuitry Volume, tone controls Character Switch, 3 position: Hot, Burn, Melt Rugged cabinet finished with black Tolex 18 ½” W x 8 ½” H x 8 ½” D 117/120 VAC, 60 Hz
Turning up the amp’s volume and letting the preamp signal overdrive the power tubes produces natural, harmonically complex - British voiced - crunch and distortion.
Addictive Chime The Heatseeker cleans up very well with changes in guitar volume. With the amp at full volume, adjusting your guitar's output produces anything from crystalline clean tones, to full on roaring distortion.
The ‘Character’ switch provides further tonal flexibility by adjusting the gain and bass output using a simple three-way switch.
Finally, the Heatseeker HS-18 thrives on overdrive and distortion pedals. Set the amp volume for a suitable clean tone and slam it into creamy, thick crunch and distortion tones with the click of a switch. Great for recording, practicing and getting a little extra slam at a gig!
Circuit Design Tubes.The Heatseeker HS-18 features a 12AX7 tube operating in a parallel triode configuration for the preamp.
Running the dual triode sections of the 12AX7 in parallel produces higher gain than a single section and lower noise than cascading one section into the other. It also produces very warm tube tone.
Another 12AX7 serves as the phase inverter and two EL84s make up the power amplifier producing about 18 watts of power.
Power Supply.The HS-18 features solid-state rectification. This means that devices called silicon diodes convert the incoming alternating current power into the direct current power the rest of the circuit needs.
Many vintage and boutique amps use tube rectifiers because they produce desirable ‘sag’. Circuitry downstream of the SS rectifiers in your Heatseeker does the same thing. You avoid the extra cost of tube rectification and the additional heat produced by the rectifier tube. You get sag that is indistinguishable from a tube rectifier set up
Controls . A volume control and single tone control reside between the preamp and phase inverter.The tone control rolls off high frequencies to voice the top end of the amp.
The lack of bass and middle tone controls restricts the amount of tone shaping, however it also reduces signal loss inherent in passive tone controls.
The fewer passive controls in the signal chain, the larger the signal getting to the phase inverter and on to the power section. This is a key factor in the Heatseeker’s ability to produce more volume than expected from an 18-watt amp and to drive the power amp into the crunch and distortion zone.
Character Switch . The Character switch does what its name implies: changes the tonal character of the amp.
There are three settings:
Hot. Ultra rich and warm tube tone. Medium gain. Burn. Aggressive high-mids, controlled bottom end, classic crunch and distortion tones. High gain. Great for dark sounding humbuckers. Melt. Big bottom, aggressive throughout the frequency spectrum. Roaring crunch and distortion. Highest gain. Great for producing ‘huge’ distorted tone from single coil guitars. There you have it: simple, effective, useful tone shaping. You’ll find that the switch positions match well with different songs and musical styles.
Heatseeker specs Handmade, hand wired using an eyelet circuit board with Teflon wire and lead-free solder Each Heatseeker undergoes a 59 point bench test prior to two playing tests 18 watts 2 X EL84 power tubes, cathode biased 2 x 12AX7 preamp tubes Solid state rectification with ‘sag’ circuitry Volume, tone controls Character Switch, 3 position: Hot, Burn, Melt Rugged cabinet finished with black Tolex 18 ½” W x 8 ½” H x 8 ½” D 117/120 VAC, 60 Hz
Join our Email List for Updates and Special Offers
